Cog 18 pin 12864 lcd
Intshayelelo yeMveliso
| Inombolo yoMfanekiso | I-RXMG-12864Q |
| Bonisa ubukhulu | 41.8x26.1mm(VA) |
| Uhlobo | STN |
| Umlawuli | ST7565 okanye ilingana |
| Ukusebenza ngoku | < 700uA(3.3V) |
| Ujongano | Uthotho |
| I-Voltage yokusebenza | 3.1~3.5V |
| Jonga isalathiso | 6H |
| Isibane ngasemva | Mhlophe |
| Imo yokubonisa | Stn negative blue |
| Ubushushu bokusebenza | -10 ~ 60℃ |
| ubushushu bokugcina | -20 ~ 70℃ |
| Isicelo | Umlinganiswa, umboniso wedijithi womshicileli, izixhobo njalo njalo |
Esinye isikrini se-12864 LCD sokubhekisa:
ISabelo sePin:
| I-Pin NO. | Phina Igama | Inkcazo yePin |
| 1 | CS1 | Ukukhetha i-chip |
| 2 | /CS | |
| 3 | /RST | Seta kwakhona isignali(H: yesiqhelo;L:ukusetha kwakhona) |
| 4 | SO | |
| 5 | A0 | Idatha/umyalelo wokukhetha(H/L) |
| 6 | SI | |
| 7 | SCK | Ungeniso lwewotshi yothotho |
| 8 | SCLK | |
| 9 | CDA | Ukufakwa kwedatha yothotho |
| 10 | NC | |
| 11 | VDD | Unikezelo lwamandla oluhle |
| 12 | I-LED + | Unikezelo lwamandla lwesibane esilungileyo |
| 13 | VSS | Unikezelo lwamandla olubi, umhlaba |
| 14 | I-LED- | Unikezelo lwamandla lwesibane esingalunganga |
| 15 | I-LED- | Unikezelo lwamandla lwesibane esingalunganga |
| 16 | NC | Nil |
| 17 | I-LED + | Unikezelo lwamandla lwesibane esilungileyo |
| 18 | NC | Nil |
Iinkonzo zethu
UKWENZA :
| Bonisa | icandelo, umzobo, umlinganiswa wemodyuli ye-lcd ye-monochrome&TFT yamkelwe |
| Imo yokubonisa | TN,STN,FSTN,HTN,transflective,reflective,transmissive,yellow green,blue,grey optional |
| Uhlobo lokubonisa | COB,COG,TAB |
| Lcd ubukhulu(cm) | 0.11,0.14 |
| Ubunzima bokukhanya ngasemva(cm) | 2.8,3.0,3.3 |
| Ujongano | IParallel(8bit,4bit,16 bit,80mode,68mode),isiriyeli(i2c,spi,uart,usb) |
| Umlawuli | Ukhetho |
| IC | Ukufa okanye ukupakishwa ngokuzithandela |
| I-Hardware okanye isoftware | Bonke bamkelwe |
| Ulwazi olunikiweyo | Yonke ingcamango, isampuli, ifoto, umzobo, ukusetyenziswa kwencwadana njalo njalo kulungile |
1, ndiyafunaImodyuli ye-LCD ibonisa amanani asi-8 kwaye ubungakanani benkcazo yi-35mm * 70mm………?
Impendulo: Akukho ngxaki. Okokuqala, pls usithumelele iphepha lakho lokuzoba okanye iisampulu; siyakwazisa eyona ifanelekileyo ukuba iyimveliso eqhelekileyo. Okanye sinokuyilungisa ngokusekwe kwenye yazo.
2,Le modyuli ye-LCD yile nto siyifunayo, kodwa inkulu, ingaba unayo isayizi encinci?Akunye nomboniso womxholo udinga ukutshintshwa kancinci.
Impendulo: Kuhlobo lwemodyuli ye-LCD yecandelo, ukuba ufuna ukuguqula ubungakanani benkcazo okanye umxholo wokubonisa, i-LCD entsha yeglasi. Siza kukwazisa ngobumba
intlawulo emva kokuqinisekisa xa intlawulo,siya kuqalisa iphepha lokuzoba ukujonga kwakho.
3, Le modyuli ye-LCD yokukhanya ngasemva ityheli-luhlaza,kodwa Iufuna ukukhanya okuluhlaza.
Impendulo: Akhongxaki, singakutshintshela.
4, ndifuna ukwenza imodyuli entsha yeLCD.Cuyayenza?
Impendulo: Ewe, sinako. Nceda uthumele iphepha lakho lomzobo. Ukuba awunayo, nceda undixelele ubungakanani bolwandlalo lwesibonisi se-LCD, ulwazi lokubonisa, ukuba ufuna isibane sangasemva okanye iPCB
ibhodi nge IC, Siya kuvavanya iindlekokwaye ndikunike ixabiso kungekudala.
5, Liliphi ixesha elikhokelayo lezixhobo zokusebenza
Impendulo: iintsuku ezili-15 ukuya kwezingama-30 emva kokuzoba isiqinisekiso sephepha kunye nentlawulo yentlawulo yezixhobo, sinokukuxelela elona xesha lichanekileyo xa uqinisekisa umzobo wephepha.
6,Ngaba ungasithumela iisampulu ukuze sijongwe?
Impendulo: Ewe,. Iisampulu zeodolo ziyafumaneka
7,Yintoni iIxesha lokukhokela?
Impendulo: Ukuba sinesitokhwe semigangatho, ixesha elihamba phambili lusuku olunye emva kokuhlawula. Ukuba yimveliso yobuninzi kwizinto ezikhethekileyo, ixesha elihamba phambili li malunga neentsuku ze-1530.
Ukuba sinokugqiba kwangaphambili, siya kuthumelaulwazi lwakho kwangaphambili
8 , Ziziphi iindlela zokuhlawula onokuzamkela?
Impendulo: Okwangoku samkela iT/T kuphela.
